Electronic Measurement Equipment Mechanic (Title 32) (Indefinite) - Army National Guard Units

NOTE: Qualifications are based on breadth/level of experience. In addition to describing duties performed, applicants must provide the exact dates of each period of employment (from MM/DD/YY to MM/DD/YY) and the number of hours worked per week if part time. As qualification determinations cannot be made when resumes do not include the required information, failure to provide this information may result in disqualification. Applicants are encouraged to use the USAJOBS Resume Builder to develop their federal resume. NOTE: All job seekers will be required to limit their resumes to 2 pages in length when applying for job opportunity announcements (JOAs). Remarks: This position is being advertised as an indefinite appointment and applicant selected may be released at any time and advised of his/her rights and benefits to which entitled. In the event a permanent employee is accepted for this indefinite position, there will be a change in their tenure from permanent to indefinite. Indefinite appointments may be made permanent at a later date without competition. NOTE: This position serves as a temporary backfill for a deployed technician. Upon the return of the deployed employee, this appointment is subject to termination. While the agency will do its best to identify placement opportunities in available vacancies, continued employment is not guaranteed. WHO CAN APPLY: GROUP I - All qualified Male/Female Enlisted Personnel Enlisted Member (E1/PV1 - E7/SFC) currently employed (permanent) in the Virginia Army National Guard Military Technician Program. GROUP II - All qualified Virginia Army National Guard Male/Female Enlisted Personnel Enlisted Member E1/PV1 - E7/SFC), regardless of employment status (Traditional, Military Technician or AGR). To be considered as a Group II applicant, proof of appointment/enlistment in the Virginia National Guard must be attached if the appointment/enlistment occurred within 60 days prior to, or during, the advertisement period. Military Grades: Enlisted Member (E1/PV1 - E7/SFC) GENERAL EXPERIENCE: Applicant must have experience or training performing calibration, diagnostics repair, and certification of electronic, mechanical, and radiation Test Measurement and Diagnostic Equipment (TMDE). SPECIALIZED EXPERIENCE: Applicant must have at least 18 months of specialized experience, equivalent to at least the WG-10 level, or equivalent pay band in other pay systems in the Federal government? This experience may also have been obtained in the private sector, but must demonstrate that it is comparable to the WG grade indicated. This experience must include activities such as: Experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior, distortion, and amplification; pulse, trigger, and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths, and skilled in the analysis of waveform characteristics such as timing, duration, frequency, and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols, mathematical expressions and formulas, calibration procedures, and other reference materials. Experience in applying established techniques and methods of repair, testing, alignment, and calibration of equipment, which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment. As a Electronic Measurement Equipment Mechanic (Title 32), WG-2602-11, you will perform the below duties: Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins, manuals, etc. Performs functional electronic, physical, and radioactive testing involving interpretation and analysis of measurement data, in accordance with cyclic inspection requirements. Aligns, troubleshoots, tests, inspects, repairs, modifies, calibrates and certifies precision measurement equipment such as multimeters, microwave equipment, oscilloscopes, temperature analyzers, mercurial barometers, gage blocks and micrometer caliper dimensional equipment, digital voltmeters, signal generators, torque wrenches, pressure gauges, torque testers, weight scales, electronic counters, radiation monitors, radix calibrators, and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions, which are often vague and incomplete, and may require the