Nondestructive Tester (Title 32) (Permanent) - Air National Guard Units

NOTE: Qualifications are based on breadth/level of experience. In addition to describing duties performed, applicants must provide the exact dates of each period of employment (from MM/DD/YY to MM/DD/YY) and the number of hours worked per week if part time. As qualification determinations cannot be made when resumes do not include the required information, failure to provide this information may result in disqualification. Applicants are encouraged to use the USAJOBS Resume Builder to develop their federal resume. NOTE: All job seekers will be required to limit their resumes to 2 pages in length when applying for job opportunity announcements (JOAs). WHO CAN APPLY: GROUP I - All qualified Male/Female Enlisted Member (E3/A1C - E5/SSgt) currently employed (permanent) in the Virginia Air National Guard Military Technician Program. GROUP II - All qualified Virginia Air National Guard Male/Female Enlisted Member (E3/A1C - E5/SSgt) regardless of employment status (Traditional, Military Technician or AGR). To be considered as a Group II applicant, proof of appointment/enlistment in the Virginia National Guard must be attached if the appointment/enlistment occurred within 60 days prior to, or during, the advertisement period. Military Grades: Enlisted Member (E3/A1C - E5/SSgt) GENERAL EXPERIENCE: Applicants must have experience or training which demonstrates the ability to set up and operate test equipment, use test apparatus to apply tests to material or products, record readings, observe and record established reactions, and classify according to defined categories. SPECIALIZED EXPERIENCE: Applicants must have at least 18 months of specialized experience, equivalent to at least the WG-08 level, or equivalent pay band in other pay systems in the Federal government. This experience may also have been obtained in the private sector, but must demonstrate that it is comparable to the WG grade indicated. This experience must include activities such as: Experience or training in using ultrasonic and/or eddy current inspection techniques to observe, measure, and detect discontinuities and flaws. Experience classifying test results, identifying material deficiencies, and recommending courses of action for items of equipment. Experience recommending engine components to be inspected and forwarding results to the appropriate authority. Experience performing scheduled inspections of testing equipment ensuring compliance with established technical regulations and procedures. As a Nondestructive Tester (Title 32), WG-7305-10, you will perform the below duties: 1. Determines test method, and prepares fluids and parts for nondestructive inspection. Interprets nondestructive inspection test results, and provides information about defects to repair center. Performs Oil Spectrometry process and analyzes wear metal content on engine lubricating oil and other fluids, and recommends corrective action. Establishes radiation areas for radiographic operations. Computes and monitors personal exposure areas for radiographic operations, and monitors personnel exposure data. Performs nondestructive inspection on structures, components, and systems. Detects flaws such as cracks, delaminations, voids, processing defects, and heat damage using penetrant, eddy current, magnetic particle, radiographic, optical, Thermography, Shearography and ultrasonic test equipment. Determines metallurgical information of components according to alloy, temper, conductivity, and associated factors. May also serve as Alternate TMDE Monitor, PCAMS, Alternate Equipment Custodian, Alternate Supplies Manager, Alternate Hazardous Waste Monitor, Alternate Hazardous Communication Monitor, Alternate Spill Prevention Monitor, Alternate FOD Monitor, Alternate Radiation Monitor, Alternate Technical Order Monitor, Alternate Precious Metals Monitor, and Training Monitor. Applies magnetic particle and/or liquid penetrant inspection to detect and interpret the relevancy of flaws in a variety of parts. Parts are numerous and varied, and are of ferrous and/or nonferrous metals, and consist of surface or near surface discontinuities in the metal; e.g., fatigue cracks, welding overlap, cold shut, or surface cracks that may stem from internal flaws, such as pipes, inclusions, or forging lap. Sets up each different liquid penetrant or magnetic particle method following Technical Orders (TOs), Time Change Technical Orders (TCTOs), or Work Control Documents (WCDs), or Nondestructive Testing Instructions (NDIs). Ensures the equipment and solutions are in compliance with technical guides and quality standards before performing tests and must submit an AFTO 22 if defects in TO's exist or an AF 107 if there is no technical data to accompany the task. Performs all processing tasks; i.e., dipping items in penetrant or magnetic particle baths, washing and drying, magnetizing and demagnetizing ferrous items, and subjecting them to Ultra Violet Black light to detect and evaluate flaws, their n