Power Plant Mechanic Trainee II/III - U.S. Army Corps of Engineers

Who May Apply: US Citizens In order to qualify, you must meet the experience requirements described below. Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., Peace Corps, AmeriCorps) and other organizations (e.g., professional; philanthropic; religious; spiritual; community; student; social). You will receive credit for all qualifying experience, including volunteer experience. There is no specific length of training or experience required. However, you must be able to demonstrate, through experience shown in your written application materials that you possess the sufficient knowledge, skills, and abilities to successfully perform the work of this position without more than normal supervision. Power Plant Mechanic Trainee II Minimum Qualifications (Screen Out Element): Ability to do the work of a(n) Power Plant Mechanic Trainee II/III without more than normal supervision. I have the ability to identify and use basic hand tools (sockets, wrenches, grease guns, impact drivers) to perform basic servicing procedures under continuous step-by-step instruction and direct oversight. - Failure to meet this Screen Out Element will result in an ineligible rating. Power Plant Mechanic Trainee III Minimum Qualifications (Screen Out Element): Ability to do the work of a(n) Power Plant Mechanic Trainee II/III without more than normal supervision. I have the ability to disassemble, clean, and reassemble routine mechanical components under direct guidance; perform basic shop math; AND perform torch cutting or pipe threading with periodic coaching. - Failure to meet this Screen Out Element will result in an ineligible rating. Ability To Do The Work Of The Position Without More Than Normal Supervision PHYSICAL EFFORT: Work requires extensive walking, standing, and climbing vertical and inclined ladders and stairs; and stooping, bending, kneeling, and crawling. Work may be done in awkward and cramped positions which may require the physical endurance to work under poor conditions for prolonged periods of time. Requires lifting and carrying tools, equipment and supplies frequently weighing up to and over 45 pounds. Required to operate large valves, apply servolocks, lift deck hatches, and perform other tasks requiring up to 75 pounds of pulling or turning force. There is danger of cuts, bruises and burns from equipment used and possible irritation or injury to eyes and spills from acids and solvents used. Must have good distant vision in each eye and be able to read fine calibrations; glasses permitted. Ability to distinguish basic colors is required. Ability to hear the conversational voice, with or without a hearing aid, is required. An amputation of arm, hand, leg or foot will normally disqualify an applicant for appointment. Any physical condition which would cause the applicant to be a hazard to his/herself or to others is disqualifying. WORKING CONDITIONS: The principal assignment is to the powerhouse; however the work area may include intake structures, and spillway areas. When working outside, is exposed to the usual extremes of climate. Exposed to high noise levels from equipment and machinery, and conditions of low visibility due to wearing protective devices and available light in some locations. Exposed to heights, oils, greases, confined areas, dust, dirt, water, heat and cold, odors, fumes, and moving and/or energized equipment. Occasionally works in proximity to high voltages and currents. Is subject to the discomfort of safety equipment required such as hard-hats, ear plugs, safety glasses and goggles, face masks, shields and helmets, respirators, and gloves depending on work performed and safety requirements which must be met. Must wear appropriate safety equipment and protective clothing, and successfully complete and maintain all occupational health requirements, including pulmonary capacity and other routine occupational and pre-employment medical examinations. Inspects, diagnoses, and performs major repairs to mechanical operating equipment of hydroelectric powerhouses, dams, spillways, and intake structures. Diagnoses mechanical failures of equipment and performs repairs by disassembling, overhauling, installing, and reassembling parts on all mechanical operating equipment of the powerhouse, dam, spillway, and intake structure. Inspects, tests, and adjusts powerhouse, dam, spillway, and intake machinery and equipment. Performs electric and acetylene welding and machine-work required in the repair and manufacture of parts for maintenance of powerhouse, dam, spillway, and intake structure equipment. Maintains potable water and sewage treatment equipment. Operates aerial lifts such as articulating boom platforms and mobile load handling equipment such as forklifts; rigs heavy loads and operates bridge and gantry cranes as needed to lift these loads. Online study and on-the-job work assignments are coordinated to relate basic theories